[i]
闲来没事就想着刷下机看能否利用起来，找遍网络没有找到刷机包，
（之前有问题有线电视维护人员刷机升级过，现在他们也找不到刷机包了）
[i]
[i]
于是拆机连接TTL线跑了下，
[i]
代码看不懂，望大神看下有没有刷机包，或者这个机顶盒怎么装软件，有没有搞头
[Asm] 纯文本查看 复制代码ROM
UART_115200
AC_ON
[23456789ABCD][123456789ABCD][23456789ABCDE][23456789ABCD]-7787
BIST0-OK[AT][MB][start ub][0]
U-Boot 2011.06 (Dec 10 2015 - 10:12:25)
DRAM: 256 MiB
Hello U-Boot
Stack Pointer at: 8d0a6980
uboot held at [8f000000~90000000]
Now running in RAM - U-Boot at: 8c1f0180
NAND: DMA MODE
CIS is found @Blk0
FCIE is set to 54MHz
128 MiB
*** Warning - set default for mtdparts, using default environment
Creating 1 MTD partitions on "nand0":
0x000000640000-0x000000840000 : "mtd=2"
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
Can't find "CTRL" partition
restore UBI scan
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=2"
UBI: MTD device size: 2 MiB
UBI: number of good PEBs: 16
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 250
UBI: number of internal volumes: 2
UBI: number of user volumes: 1
UBI: available PEBs: 1
UBI: total number of reserved PEBs: 15
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 309/301
NAND read: device 0 offset 0x180000, size 0xa8
168 bytes read: OK
Volume "MPOOL" found at volume id 0
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Set MAC default
MAC: 0x0: 0xfa: 0xe0: 0xfa:0xe0: 0x0
UBI: mtd1 is detached from ubi0
Creating 1 MTD partitions on "nand0":
0x000000840000-0x000007e40000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
Can't find "CTRL" partition
restore UBI scan
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 118 MiB
UBI: number of good PEBs: 944
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 250
UBI: number of internal volumes: 2
UBI: number of user volumes: 8
UBI: available PEBs: 75
UBI: total number of reserved PEBs: 869
UBI: number of PEBs reserved for bad PEB handling: 24
UBI: max/mean erase counter: 20/10
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 2, name "CON"
UBIFS: file system size: 15491072 bytes (15128 KiB, 14 MiB, 122 LEBs)
UBIFS: journal size: 2412544 bytes (2356 KiB, 2 MiB, 19 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 0 bytes (0 KiB)
/sys.ini not found!
[ERROR] vfs_getsize:310: ubifsfilesize /sys.ini fail
[ERROR] loadscript:744: No enough buffer or path fail(/sys.ini) :
[src/MsUtility.c] [loadscript]
Unmounting UBIFS volume CON!
Partition UBI has been attached, skip attaching process
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 2, name "CON"
UBIFS: file system size: 15491072 bytes (15128 KiB, 14 MiB, 122 LEBs)
UBIFS: journal size: 2412544 bytes (2356 KiB, 2 MiB, 19 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 0 bytes (0 KiB)
Usage:
get file size in UBIFS volume
[ERROR] vfs_getsize:310: ubifsfilesize fail
[ERROR] prepare_nand_dbtable:560: get logo_size fail...>>>:0
[ERROR] write_dbtable:638: flash database not ready...>>>
[ERROR] do_dbtable_init:230: dbtable init fail
It's the last cmd
IIC port == 1
MDrv_IIC_Init PORT 1
MDrv_IIC_InitPort0: OK
No recovery information, needless to recovery
ipanel-dbg: usb upgrade
(Re)start USB...
Check USB port[0]:
No USB is connecting
usb init failed
Error, couldn't init Lowlevel part
** Invalid boot device **
** Invalid boot device **
** Invalid boot device **
** Invalid boot device **
** Invalid boot device **
** Invalid boot device **
** Invalid boot device **
** Invalid boot device **
** Invalid boot device **
** Invalid boot device **
** Invalid boot device **
** Invalid boot device **
** Invalid boot device **
** Invalid boot device **
** Invalid boot device **
[ERROR] do_udstar:475: no file in usb
BootFlag 0▒▒▒
huangxb start app now
Unmounting UBIFS volume CON!
Partition UBI has been attached, skip attaching process
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 2, name "CON"
UBIFS: file system size: 15491072 bytes (15128 KiB, 14 MiB, 122 LEBs)
UBIFS: journal size: 2412544 bytes (2356 KiB, 2 MiB, 19 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 0 bytes (0 KiB)
ubifs_filesize 0000fc34
Changelist: 00112233
============= set bootargs ===============
Unmounting UBIFS volume CON!
Partition UBI has been attached, skip attaching process
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 2, name "CON"
UBIFS: file system size: 15491072 bytes (15128 KiB, 14 MiB, 122 LEBs)
UBIFS: journal size: 2412544 bytes (2356 KiB, 2 MiB, 19 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 0 bytes (0 KiB)
ubifs_filesize 0000fc34
Volume MPOOL not found!
Unmounting UBIFS volume CON!
UBI: mtd1 is detached from ubi0
Creating 1 MTD partitions on "nand0":
0x000000640000-0x000000840000 : "mtd=2"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
Can't find "CTRL" partition
restore UBI scan
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=2"
UBI: MTD device size: 2 MiB
UBI: number of good PEBs: 16
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 250
UBI: number of internal volumes: 2
UBI: number of user volumes: 1
UBI: available PEBs: 1
UBI: total number of reserved PEBs: 15
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 309/301
Write Env to BA000...
Write Backup Env to D9000...
done
Write Env to BA000...
Write Backup Env to D9000...
done
Write Env to BA000...
Write Backup Env to D9000...
done
Write Env to BA000...
Write Backup Env to D9000...
done
Write Env to BA000...
Write Backup Env to D9000...
done
Unknown command 'if_51OnRam_set' - try 'help'
Hit any key to stop autoboot: 0
ipanel-dbg:fact_test on, burn
EMAC Mem Base:ac56c000
Rx buff:c56c000
RBQP:c59c000
Packet buffer:8c76836c
phy [0]=78c9
MAC Address 00:FA:E0:FA:E0:00
Auto-Negotiation...
Link Status Speed:100 Full-duplex:1
word_ETH_CFG 803(Re)start EMAC...
ipanel-dbg:stb have burned,no need to burn
AC on
MDrv_PNL_Init u32PnlRiuBaseAddr = bf200000
MDrv_PNL_Init u32PMRiuBaseAddr = bf000000
[_MDrv_PNL_Init_LPLL][304]pstPanelInitData->u16Width=1920, pstPanelInitData->u16Height=1080
[_MDrv_PNL_Init_LPLL][306]u16HTotal=2640,u16VTotal=1125,pstPanelInitData->u16HTotal=2640,pstPanelInitData->u16VTotal=1125, u16DefaultVFreq=500
[_MDrv_PNL_Init_Output_Dclk][349]pstPanelInitData->u16Width=1920, pstPanelInitData->u16Height=1080
[_MDrv_PNL_Init_Output_Dclk][351]u16HTotal=2640,u16VTotal=1125,pstPanelInitData->u16HTotal=2640,pstPanelInitData->u16VTotal=1125, u16DefaultVFreq=500
msHdmitx_Disp_Init
[XC,Version]
no need to patchRx Support HDMI mode!
shift -8 pixels in PAL mode
No UBIFS volume mounted!
UBI: mtd1 is detached from ubi0
Creating 1 MTD partitions on "nand0":
0x000000840000-0x000007e40000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
Can't find "CTRL" partition
restore UBI scan
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 118 MiB
UBI: number of good PEBs: 944
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 250
UBI: number of internal volumes: 2
UBI: number of user volumes: 8
UBI: available PEBs: 75
UBI: total number of reserved PEBs: 869
UBI: number of PEBs reserved for bad PEB handling: 24
UBI: max/mean erase counter: 20/10
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 2, name "CON"
UBIFS: file system size: 15491072 bytes (15128 KiB, 14 MiB, 122 LEBs)
UBIFS: journal size: 2412544 bytes (2356 KiB, 2 MiB, 19 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 0 bytes (0 KiB)
ubifs_filesize 00000c71
Loading file '/mmap.ini' to address 0x8ae2bb98 (size 3185)
Loading file '/mmap.ini' to addr 0x8ae2bb98 with size 3185 (0x00000c71)...
Done
Unmounting UBIFS volume CON!
Create Dolby single part name task failed!![Hal_VE_EnableDI][1446] bEnable = 0, bIsDNR2VE = 0
Partition UBI has been attached, skip attaching process
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 2, name "CON"
UBIFS: file system size: 15491072 bytes (15128 KiB, 14 MiB, 122 LEBs)
UBIFS: journal size: 2412544 bytes (2356 KiB, 2 MiB, 19 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 0 bytes (0 KiB)
ubifs_filesize 0000fc34
Loading file 'customer/bootlogo.jpg' to address 0xab350400 (size 64564)
Loading file 'customer/bootlogo.jpg' to addr 0xab350400 with size 64564 (0x0000fc34)...
Done
[AutoTest][MBoot][JPD Decode]
[ERROR] pattern_search:824: Can't find the E_MMAP_ID_PVR_DOWNLOAD_ADR
[ERROR] _get_mmap:542: get addr from mmap fail
[ERROR] get_mmap:407: _get_mmap fail
[ERROR] showLogo:505: get E_MMAP_ID_PVR_DOWNLOAD fail
[GOP3, PID 0, TID 0x-1][Driver Version]: 0089, BuildNum: 0002, ChangeList: 00524916
[AutoTest][MBoot][Show Logo][0]
do_bootvideo()
Can't find BOOT_VIDEO_WAIT_SYNC
Can't find BOOT_VIDEO_AUTOSCAN
*** hash key v1.0, use Customer_Info.h directly ***
01332317007c
Auth OK************************ Start TSP_Init ************************ : >> FwVersion:002F2500 , Date:20130722
************************* End TSP_Init *************************Unmounting UBIFS volume CON!
Partition UBI has been attached, skip attaching process
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 2, name "CON"
UBIFS: file system size: 15491072 bytes (15128 KiB, 14 MiB, 122 LEBs)
UBIFS: journal size: 2412544 bytes (2356 KiB, 2 MiB, 19 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 0 bytes (0 KiB)
ubifs_filesize 00c00000
Loading file 'customer/bootvideo.ts' to address 0xa7a33000 (size 12583028)
Loading file 'customer/bootvideo.ts' to addr 0xa7a33000 with size 12582912 (0x00c00000)...
Done
Live? 0 AutoScan? 0 V(pid:256 codec:1), A(pid:257, codec:1), PCR:256, Volume = 60
Output Control : Set HD(0), SD(0), HDMI(0)]
[MAPI PNL][001115] Initialization more than once
[XC,Version]
no need to patch=========> vdec_u8Idx=0x0, u32VdecStreamId=01010
VDEC FW add = 0x8a40000 Size = 0x100000
VDEC FB add = 0x8b40000 Size = 0x1800000
VDEC BS add = 0xa340000 Size = 0x400000
VDEC Proc add = 0xa340000 Size = 0xa000
HAL_VPU_EX_SetDbgLevel eLevel=0x0
pstVdecStreamId = 0x8c567a50, Video stream type = 1 and codec type = 1 start succeeded!
_MsDrv_AudioInit(396): Single decode case.
create Audio SHM data ...ADEC DEC add = 0x6400000 Size = 0x220000
ADEC SE add = 0x6400000 Size = 0x0
$65535
$2320
$3657
$3605
$3530
$3681
$3454
$3606
$3652
$3413
$3507
$3653
$3605
$3409
$3738
$3380
$3777
$3279
$3657
$3553
$3544
$3525
$3559
$3606
$3455
$3559
$3503
$3605
$3757
$3390
$3422
$3714
$3626
$3578
$3364
$3652
$3411
$3749
$3438
$3576
$3511
$3571
$3594
[Warning!!]No$3449
SRS TSXT license!! DecID 0 disconn$3636
ect MApi_AUDIO_ReleaseDecodeSystem() 1442
D$7089
ecID 1 disconnect MApi_AUDIO_ReleaseDeco$3730
deSystem() 1442
$3334
DecID 2 disconnect $3699
MApi_AUDIO_ReleaseDecodeSystem() 1442$3505
$3467
===== Check Audio Decoder Prot$3654
ection from hash-key IP =====Hash-key $3559
Support DD.Hash-key Support DD+.Hash-k$3497
ey Support Generic HE-AAC!!Hash Key C$3510
heck WMA Fail, no WMA license!!Hash-ke$3536
y Support DRA.Hash Key Check Dolby MS1$3585
1 Fail, no Dolby MS11 license!!Hash Ke$3554
y Check DTSE Fail, no DTSE license!!Ha$3556
sh Key Check DTSNeoUltra Fail, no DTSN$3560
eoUltra license!!Hash Key Check SRS_TSH$3603
D Fail, no SRS_TSHD license!!Hash Key C$3646
heck SRS_THEATERSOUND Fail, no SRS_TH$3468
EATERSOUND license!!Hash Key Check DTS_$3607
StudioSound3D Fail, no DTS_StudioSou$3457
nd3D license!!===== Check Protection IP$3598
End =====$3439
$3631
$3527
$7164
$3651
$6876
$3677
Audio stream type = 1 and codec type = 1 start succeeded!
E_VDEC_EX_EVENT_DISP_INFO_CHG
$14374
$3457
$3636
E_VDEC_EX_EVENT_DISP_INFO_CHG
E_VDEC_EX_EVENT_FIRST_FRAME
$3401
$3541
$3475
Wrong MIU device:1
HAL_MIU_Mask$3731
Req not support client ID:49!
Wrong MIU device:1
HAL_MIU_SelMIU not support clie$7035
nt ID:49!
$3636
$10611
$3496
$3545
$3591
$3520
$3488
BootVideo Audio master Sync$7251
down)
RATE:0 STC:15 PTS(V:618 A:5d2)(Seq:0 I:1 1stF:1)AV(on:1 S:0 R:0)$7096
(Dec:4 Err:0 Skp:0 Drp:0 Disp:1)ES(R:a3$3625
53800 W:a3ac0f0 V:3a6f10)DELTA(V:1539 A: 380) ADEC(Dec:7)
Video Decode count > 0. Normal BootVideo display
$14177
$7174
$3356
$3671
$3437
$17858
$10592
$10758
$7097
Audio u8VolHi=20,u8VolLo=2$44766
Unmounting UBIFS volume CON!
Partition UBI has been attached, skip attaching process
No size specified -> Using max size (4317184)
## Booting kernel from Legacy Image at 83ffffc0 ...
Image Name: Linux-3.1.10-mstar
Image Type: MIPS Linux Kernel Image (uncompressed)
Data Size: 1982598 Bytes = 1.9 MiB
Load Address: 80000000
Entry Point: 84000000
-usb_stop(USB_PORT0)
-usb_stop(USB_PORT1)
Loading Kernel Image ... OK
[AT][MB][start kr][0]
Starting kernel ...
Hello UART
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.1.10 (root@DevelopNineServer) (gcc version 4.3.2 (Sourcery G++ Lite 4.3-51) ) #9 PREEMPT Mon Mar 27 14:32:57 CST 2017
[ 0.000000]
[ 0.000000] LINUX started...
[ 0.000000] boot_command_line: console=ttyS0,115200 ubi.mtd=UBI ubi.mtd=UBILD root=ubi:RFS rootfstype=ubifs rw LX_MEM=0x3700000 EMAC_MEM=0x100000 DRAM_LEN=0x10000000 LX_MEM2=0xBD00000,0x4300000 BB_ADDR=0 MS_GOP0_MIU=0 mtdparts=edb64M-nand:2432k@1536k(MBOOT),2432k(MBOOTBAK),2048k(UBILD),118m(UBI),-(NA) EnvMmapEn=disable EnvMmap= BOOTLOGO_IN_MBOOT ENV_VAR_OFFSET=0xBA000 ENV_VAR_SIZE=0x10000 ENV=NAND SECURITY=OFF BOOT_VIDEO_VDEC_PTS_ADDR=0x8ae1094 BOOT_VIDEO_VDEC_PTS_KUNIT=90 BV_V_FCNT=145625088 BV_V_SFCNT=145625108 BV_F_Adr=0x7A33000 BV_F_Sz=0xC00074 BV_F_STime=0x618 BOOTTIME_SBOOT=0 BOOTTIME_UBOOT=0
[ 0.000000]
[ 0.000000] LX_MEM = 0x0, 0x3700000
[ 0.000000] LX_MEM2 = 0xBD00000, 0x4300000
[ 0.000000] CPHYSADDR(PFN_ALIGN(&_end))= 0x69E000
[ 0.000000] EMAC_LEN= 0x100000
[ 0.000000] DRAM_LEN= 0x10000000
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019755 (MIPS 74Kc)
[ 0.000000] FPU revision is: 01739700
[ 0.000000] Begin chip_setup
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 03700000 @ 00000000 (usable)
[ 0.000000] memory: 04300000 @ 0bd00000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00010000
[ 0.000000] Normal empty
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00003700
[ 0.000000] 0: 0x0000bd00 -> 0x00010000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 30720
[ 0.000000] Kernel command line: console=ttyS0,115200 ubi.mtd=UBI ubi.mtd=UBILD root=ubi:RFS rootfstype=ubifs rw LX_MEM=0x3700000 EMAC_MEM=0x100000 DRAM_LEN=0x10000000 LX_MEM2=0xBD00000,0x4300000 BB_ADDR=0 MS_GOP0_MIU=0 mtdparts=edb64M-nand:2432k@1536k(MBOOT),2432k(MBOOTBAK),2048k(UBILD),118m(UBI),-(NA) EnvMmapEn=disable EnvMmap= BOOTLOGO_IN_MBOOT ENV_VAR_OFFSET=0xBA000 ENV_VAR_SIZE=0x10000 ENV=NAND SECURITY=OFF BOOT_VIDEO_VDEC_PTS_ADDR=0x8ae1094 BOOT_VIDEO_VDEC_PTS_KUNIT=90 BV_V_FCNT=145625088 BV_V_SFCNT=145625108 BV_F_Adr=0x7A33000 BV_F_Sz=0xC00074 BV_F_STime=0x618 BOOTTIME_SBOOT=0 BOOTTIME_UBOOT=0
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 115928k/124928k available (4118k kernel code, 9000k reserved, 1692k data, 220k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU freq count = 468000000
[ 0.000000] CPU frequency 936.00 MHz
[ 0.000000] [AT][KR][reset timer][0]
[ 0.000000] console [ttyS0] enabled, bootconsole disabled
[ 0.000000] console [ttyS0] enabled, bootconsole disabled
[ 0.003000] Calibrating delay loop... 466.94 BogoMIPS (lpj=233472)
[ 0.015000] pid_max: default: 32768 minimum: 301
[ 0.016000] Mount-cache hash table entries: 512
[ 0.017000] before forking init thread, kernel takes about 17 ms
[ 0.018000]
[ 0.018000] Kernel_Level test
[ 0.021000] NET: Registered protocol family 16
[ 0.049000] bio: create slab [b] at 0
[ 0.051000] SCSI subsystem initialized
[ 0.052000] usbcore: registered new interface driver usbfs
[ 0.053000] usbcore: registered new interface driver hub
[ 0.054000] usbcore: registered new device driver usb
[ 0.055000] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.057000] cfg80211: Calling CRDA to update world regulatory domain
[ 0.058000] Switching to clocksource MIPS
[ 0.085000] NET: Registered protocol family 2
[ 0.089000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.096000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.104000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.110000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.117000] TCP reno registered
[ 0.120000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.126000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.132000] NET: Registered protocol family 1
[ 0.137000] RPC: Registered named UNIX socket transport module.
[ 0.143000] RPC: Registered udp transport module.
[ 0.148000] RPC: Registered tcp transport module.
[ 0.152000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.160000] Creating worker thread
[ 0.163000] Succsesfuly Created
[ 0.170000] ashmem: initialized
[ 0.189000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.197000] msgmni has been set to 226
[ 0.202000] io scheduler noop registered (default)
[ 0.208000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.215000] serial8250: ttyS0 at I/O 0xbf201300 (irq = 8) is a 16550
[ 0.222000] serial8250: ttyS1 at I/O 0xbf220c00 (irq = 79) is a 16550
[ 0.240000] brd: module loaded
[ 0.250000] loop: module loaded
[ 0.255000] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 0.262000] CAN device driver interface
[ 0.266000] PPP generic driver version 2.4.2
[ 0.270000] PPP Deflate Compression module registered
[ 0.276000] PPP BSD Compression module registered
[ 0.281000] PPP MPPE Compression module registered
[ 0.286000] NET: Registered protocol family 24
[ 0.290000] tun: Universal TUN/TAP device driver, 1.6
[ 0.295000] tun: (C) 1999-2004 Max Krasnyansky
[ 0.302000] Mstar-ehci-2 H.W init
[ 0.305000] Titania3_series_start_ehc start
[ 0.325000] BC disable
[ 0.327000] Mstar-ehci-2 Mstar-ehci-2.1: Mstar EHCI
[ 0.332000] Mstar-ehci-2 Mstar-ehci-2.1: new USB bus registered, assigned bus number 1
[ 0.340000] Mstar-ehci-2 Mstar-ehci-2.1: irq 74, io mem 0xbf201a00
[ 0.352000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.358000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.366000] usb usb1: Product: Mstar EHCI
[ 0.370000] usb usb1: Manufacturer: Linux 3.1.10 ehci_hcd
[ 0.375000] usb usb1: SerialNumber: mstar
[ 0.380000] hub 1-0:1.0: USB hub found
[ 0.384000] hub 1-0:1.0: 1 port detected
[ 0.389000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.395000] Mstar-ehci-1 H.W init
[ 0.399000] Titania3_series_start_ehc start
[ 0.418000] BC disable
[ 0.420000] Mstar-ehci-1 Mstar-ehci-1.0: Mstar EHCI
[ 0.425000] Mstar-ehci-1 Mstar-ehci-1.0: new USB bus registered, assigned bus number 2
[ 0.433000] Mstar-ehci-1 Mstar-ehci-1.0: irq 15, io mem 0xbf204800
[ 0.446000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.452000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.460000] usb usb2: Product: Mstar EHCI
[ 0.464000] usb usb2: Manufacturer: Linux 3.1.10 ehci_hcd
[ 0.469000] usb usb2: SerialNumber: mstar
[ 0.474000] hub 2-0:1.0: USB hub found
[ 0.478000] hub 2-0:1.0: 1 port detected
[ 0.482000] Initializing USB Mass Storage driver...
[ 0.488000] usbcore: registered new interface driver usb-storage
[ 0.494000] USB Mass Storage support registered.
[ 0.500000] NAND FLASH : DMA MODE
[ 0.506000] Creating 5 MTD partitions on "edb64M-nand":
[ 0.511000] 0x000000180000-0x0000003e0000 : "MBOOT"
[ 0.517000] mtd: Giving out device 0 to MBOOT
[ 0.522000] 0x0000003e0000-0x000000640000 : "MBOOTBAK"
[ 0.528000] mtd: Giving out device 1 to MBOOTBAK
[ 0.534000] 0x000000640000-0x000000840000 : "UBILD"
[ 0.539000] mtd: Giving out device 2 to UBILD
[ 0.545000] 0x000000840000-0x000007e40000 : "UBI"
[ 0.550000] mtd: Giving out device 3 to UBI
[ 0.555000] 0x000007e40000-0x000008000000 : "NA"
[ 0.560000] mtd: Giving out device 4 to NA
[ 0.570000] Mstar_emac0: emac_dev->base_addr = bf204000
[ 0.576000] Mstar_emac0: emac_dev->irq = 22
[ 0.580000] Mstar_emac0: use internel phy
[ 0.584000] Mstar_emac0: [ PHY Addr ] ==> :0
[ 0.589000] Mstar_emac0: alloRAM_VA_BASE = 0xA3700000 alloRAM_PA_BASE= 0x3700000 alloRAM_SIZE= 0x80000
[ 0.598000] Mstar_emac0: RBQP_BASE = 3704000
[ 0.603000] Mstar_emac0: ==> AutoNegotiation still in progress
[ 0.609000] Mstar_emac1: emac_dev->base_addr = bf243600
[ 0.615000] Mstar_emac1: emac_dev->irq = 23
[ 0.619000] Mstar_emac1: use external phy
[ 0.624000] Mstar_emac1: Wrong PHY Addr and reset to 0
[ 0.629000] Mstar_emac1:
[ 0.631000] Init EMAC error!
[ 0.635000] ALSA device list:
[ 0.638000] No soundcards found.
[ 0.641000] Netfilter messages via NETLINK v0.30.
[ 0.646000] nf_conntrack version 0.5.0 (1811 buckets, 7244 max)
[ 0.652000] ctnetlink v0.93: registering with nfnetlink.
[ 0.658000] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 0.665000] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 0.671000] xt_time: kernel timezone is -0000
[ 0.676000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 0.682000] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
[ 0.688000] arp_tables: (C) 2002 David S. Miller
[ 0.693000] TCP cubic registered
[ 0.696000] NET: Registered protocol family 17
[ 0.701000] can: controller area network core (rev 20090105 abi 8)
[ 0.707000] NET: Registered protocol family 29
[ 0.712000] lib80211: common routines for IEEE802.11 drivers
[ 0.721000] UBI: attaching mtd3 to ubi0
[ 0.725000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 0.731000] UBI: logical eraseblock size: 126976 bytes
[ 0.737000] UBI: smallest flash I/O unit: 2048
[ 0.742000] UBI: VID header offset: 2048 (aligned 2048)
[ 0.748000] UBI: data offset: 4096
[ 0.753000] Current partition UBI is not desired partition, named .
[ 0.759000] restore UBI scan
[ 0.906000] UBI: max. sequence number: 9178
[ 0.911000] UBI: the backup volume was not found
[ 0.923000] UBI: attached mtd3 to ubi0
[ 0.927000] UBI: MTD device name: "UBI"
[ 0.932000] UBI: MTD device size: 118 MiB
[ 0.937000] UBI: number of good PEBs: 944
[ 0.942000] UBI: number of bad PEBs: 0
[ 0.946000] UBI: number of corrupted PEBs: 0
[ 0.950000] UBI: max. allowed volumes: 128
[ 0.955000] UBI: wear-leveling threshold: 250
[ 0.960000] UBI: number of internal volumes: 2
[ 0.964000] UBI: number of user volumes: 8
[ 0.969000] UBI: available PEBs: 75
[ 0.973000] UBI: total number of reserved PEBs: 869
[ 0.978000] UBI: number of PEBs reserved for bad PEB handling: 24
[ 0.984000] UBI: max/mean erase counter: 20/10
[ 0.989000] UBI: image sequence number: 0
[ 0.993000] UBI: background thread "ubi_bgt0d" started, PID 498
[ 0.999000] UBI: attaching mtd2 to ubi1
[ 1.003000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 1.009000] UBI: logical eraseblock size: 126976 bytes
[ 1.014000] UBI: smallest flash I/O unit: 2048
[ 1.019000] UBI: VID header offset: 2048 (aligned 2048)
[ 1.025000] UBI: data offset: 4096
[ 1.030000] Current partition UBILD is not desired partition, named .
[ 1.036000] restore UBI scan
[ 1.042000] UBI: max. sequence number: 4835
[ 1.047000] UBI: the backup volume was not found
[ 1.056000] UBI: attached mtd2 to ubi1
[ 1.060000] UBI: MTD device name: "UBILD"
[ 1.065000] UBI: MTD device size: 2 MiB
[ 1.070000] UBI: number of good PEBs: 16
[ 1.074000] UBI: number of bad PEBs: 0
[ 1.079000] UBI: number of corrupted PEBs: 0
[ 1.083000] UBI: max. allowed volumes: 128
[ 1.088000] UBI: wear-leveling threshold: 250
[ 1.092000] UBI: number of internal volumes: 2
[ 1.097000] UBI: number of user volumes: 1
[ 1.101000] UBI: available PEBs: 1
[ 1.106000] UBI: total number of reserved PEBs: 15
[ 1.111000] UBI: number of PEBs reserved for bad PEB handling: 2
[ 1.117000] UBI: max/mean erase counter: 310/302
[ 1.121000] UBI: image sequence number: 0
[ 1.125000] UBI: background thread "ubi_bgt1d" started, PID 501
[ 1.131000] [init_mstar_nand_char]
[ 1.135000]
[ 1.137000] [SERIAL INPUT MANAGE] Managed tty_struct(.name:ttyS0) Setup!!!
[ 1.144000] [SERIAL INPUT MANAGE] disable_serial : ~~bye(len:5)
[ 1.150000] [SERIAL INPUT MANAGE] enable_serial : (len: 0)
[ 1.155000] [KDEBUGD] enter : _MStar
[ 1.155000]
[ 1.164000] UBIFS: recovery needed
[ 1.197000] UBIFS: recovery completed
[ 1.201000] UBIFS: mounted UBI device 0, volume 1, name "RFS"
[ 1.207000] UBIFS: file system size: 8126464 bytes (7936 KiB, 7 MiB, 64 LEBs)
[ 1.214000] UBIFS: journal size: 1523712 bytes (1488 KiB, 1 MiB, 12 LEBs)
[ 1.221000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 1.227000] UBIFS: default compressor: lzo
[ 1.231000] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 1.237000] VFS: Mounted root (ubifs filesystem) on device 0:14.
[ 1.244000] Freeing unused kernel memory: 220k freed
[ 1.249000] [AT][KR][start init][0]
[ 1.252000] [AutoTest][Kernel][start Initprocess][0]
starting pid 504, tty '': '/etc/init.d/rcS'
f3f^@^@▒▒^@x^@▒▒[ 1.401000] UBIFS: recovery needed
[ 1.435000] UBIFS: recovery completed
[ 1.439000] UBIFS: mounted UBI device 0, volume 2, name "CON"
[ 1.445000] UBIFS: file system size: 15491072 bytes (15128 KiB, 14 MiB, 122 LEBs)
[ 1.453000] UBIFS: journal size: 2412544 bytes (2356 KiB, 2 MiB, 19 LEBs)
[ 1.460000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 1.466000] UBIFS: default compressor: lzo
[ 1.470000] UBIFS: reserved for root: 0 bytes (0 KiB)
insmod: can't read '/lib/modules/ntfs-3g.ko': No such file or directory
[ 1.511000] usbcore: registered new interface driver usbhid
[ 1.517000] usbhid: USB HID core driver
Open dbus!!
Mounting application
[ 1.596000] UBIFS: recovery needed
[ 1.643000] UBIFS: recovery completed
[ 1.647000] UBIFS: mounted UBI device 0, volume 3, name "APP"
[ 1.652000] UBIFS: file system size: 57393152 bytes (56048 KiB, 54 MiB, 452 LEBs)
[ 1.660000] UBIFS: journal size: 7618560 bytes (7440 KiB, 7 MiB, 60 LEBs)
[ 1.667000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 1.673000] UBIFS: default compressor: lzo
[ 1.677000] UBIFS: reserved for root: 0 bytes (0 KiB)
Mounting MWlib
Mounting PTS
[ 1.695000] Mstar_emac0: ==> AutoNegotiation still in progress
Scan and build device node
?▒
▒mknod: /dev/ubi_ctrl: File exists
^\^\▒^@▒^@▒▒U^E▒▒▒^@▒^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@f3f^@^@▒▒^@x^@▒▒[ 3.715000] [GFLIP] GFLIP DRIVER OPEN
▒▒
▒^\^\▒^@▒^@▒▒U^E▒▒▒^@▒^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@f3f^@^@▒▒^@x^@▒▒'?▒^\^\▒^@▒^@▒▒U^E▒▒▒^@▒^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@f3f^@^@▒▒^@x^@▒▒?▒
▒^\^\▒^@▒^@▒▒U^E▒▒▒^@▒^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@f3f^@^@▒▒^@x^@▒▒?▒
^\^\▒^@▒^@▒▒U^E▒▒▒^@▒^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@f3f^@^@▒▒^@x^@▒▒▒▒
▒^\^\▒^@▒^@▒▒U^E▒▒▒^@▒^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@f3f^@^@▒▒^@x^@▒▒?▒
▒^\^\▒^@▒^@▒▒U^E▒▒▒^@▒^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@f3f^@^@▒▒^@x^@▒▒▒▒
▒^\^\▒^@▒^@▒▒U^E▒▒▒^@▒^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@f3f^@^@▒▒^@x^@▒▒▒▒
▒▒&▒ڪ▒▒/▒▒▒/▒▒▒▒▒▒▒▒k2▒▒2▒
22222S▒▒▒▒▒▒22222▒%20123456789ABCDEF▒▒▒▒▒?▒" ▒▒▒▒▒▒▒U▒▒▒u▒b▒▒▒?�҇ҩҨү▒▒"0▒`▒▒▒$▒
▒C▒▒▒ ▒▒▒▒▒1▒▒!▒",Z▒[▒\▒▒▒▒▒▒{▒|▒}▒~▒▒▒4#▒%▒&xy▒"x&y▒tF▒yx y{▒"xy▒"x&y▒t▒yx&y▒▒d"x▒▒▒▒0\▒▒"x&y▒"x&▒x#y▒▒tG▒▒"x▒▒#y▒▒tW▒▒"▒▒▒▒▒▒▒▒▒ԅ▒▒0▒▒5▒▒0▒▒▒▒▒▒▒▒▒ЂЃ2▒▒ ▒▒0^080▒▒▒▒dp▒6僅4▒▒5▒𣅃4▒▒5▒
▒6▒▒▒N▒▒▒▒▒▒Nt▒.▒▒▒▒gt▒t▒▒▒▒▒▒▒▒t▒▒I▒:▒u:▒⪅▒▒▒▒n▒▒n▒T▒▒▒▒▒▒▒wЂЃ▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒4u:u▒
▒▒▒▒gt▒t▒t▒▒▒▒▒▒▒▒▒▒n▒▒▒gt▒t▒▒0▒▒1▒▒2▒▒n▒L▒▒▒▒▒▒,▒▒gt▒t▒t▒▒nˉ▒▒n▒T▒D▒▒▒ˉ▒ c▒▒gt:▒t
▒▒!▒▒3▒▒▒▒▒
▒▒▒▒
▒▒▒▒▒▒▒▒ЂЃ▒▒▒▒▒▒▒▒▒▒▒▒
▒▒▒▒▒▒▒▒▒▒▒}
▒▒▒▒▒▒▒x▒▒▒n▒
;▒▒0▒▒▒▒E▒ED▒▒▒B▒▒▒C▒,▒6▒▒▒▒▒6u▒▒▒▒▒gt▒t▒▒▒▒▒▒n▒
*▒▒▒▒▒▒i▒▒▒▒▒▒▒▒▒▒▒▒x▒▒▒g▒▒▒t
▒▒Ѫ▒▒▒▒n▒▒e▒▒gt▒t▒t▒▒n▒▒e▒▒gt▒t▒t▒▒n▒$▒▒
▒▒▒▒▒▒▒▒gt▒t%▒▒▒▒▒▒n▒&&▒▒ˉ▒T▒D▒▒▒▒▒gt▒t▒t▒▒n▒▒▒▒▒▒▒▒0%▒:▒ÔP
u:u▒▒▒▒gt▒t▒t▒▒n▒1%▒:▒ÔP
u:u▒ ▒▒▒▒gt▒t▒t▒▒n▒2▒n▒3!▒3▒▒3▒▒▒gt▒t▒t▒▒▒▒▒n▒4▒n▒▒▒▒▒▒▒=\0@▒▒▒A▒▒y▒▒▒▒▒T##▒a▒/▒-u@▒▒R▒0▒▒S▒1▒▒T▒2▒▒Ut▒u:▒n▒▒gt
▒t=▒▒▒▒▒▒n▒▒gt▒t▒t▒▒▒1Җґ▒"▒▒▒▒▒ԫ▒▒▒▒▒▒▒▒▒▒▒Ô
